If you’re planning to remove the antlers from a deer mount you’ll need to know how to do it properly. With a few tools and some careful planning you can remove the antlers from your mount and have it looking good as new in no time.
First you’ll need to gather a few supplies. You’ll need a sawzall or reciprocating saw a drill a 1/2″ drill bit a hacksaw a mallet and some sandpaper. You’ll also need a helper to hold the mount while you work.
Once you have your supplies you’re ready to get started. Begin by drilling a hole in the center of each antler base. The hole should be big enough to fit the blade of your sawzall or reciprocating saw.
Next insert the blade of your saw into the hole and start cutting through the antler. Be careful not to cut too deeply as you don’t want to damage the mount. Cut through both antlers then use the mallet to gently tap the antlers free from the mount.
If there are any stubborn pieces remaining you can use the hacksaw to carefully cut through them. Once the antlers are free sand down any rough edges and holes left behind.
With a little bit of time and effort you can easily remove the antlers from a deer mount. With the right supplies and some careful planning you can have your mount looking good as new in no time.
How do you remove antlers from a deer mount?
You will need a few supplies including a power drill sawzall or reciprocating saw and a grinder.
You will also need to putty or epoxy to fill in the holes.
Is it difficult to remove antlers from a deer mount?
It can be difficult especially if the antlers are tightly sealed onto the skull.
You will need to be very careful not to damage the skull or the antlers.
How long does it take to remove antlers from a deer mount?
It depends on the size of the antlers and how difficult it is to remove them.
But generally it shouldn’t take more than an hour or two.
What is the best way to remove antlers from a deer mount?
The best way is to use a power drill to make a hole in the antler then insert a sawzall or reciprocating saw and cut through the antler.
After that you can use a grinder to smooth out the edges.
What is the worst way to remove antlers from a deer mount?
The worst way is to try to pry the antlers off with a screwdriver or other sharp object.
This will damage the antlers and the skull.
Can you remove antlers from a deer mount without damaging it?
Yes if you are careful and use the right tools.
What happens if you damage the deer mount while removing the antlers?
The damage will depend on how bad it is.
If it’s just a few scratches you can touch them up with some paint.
But if the damage is more severe you may need to get a new deer mount.
Will removing the antlers from the deer mount void the warranty?
It depends on the warranty.
You should check with the manufacturer to be sure.
I just got a new deer mount.
Can I remove the antlers myself or do I need to take it to a taxidermist?
You can remove the antlers yourself if you want but it’s probably best to take it to a taxidermist.
How much does it cost to have a taxidermist remove the antlers from a deer mount?
It depends on the taxidermist and the size of the antlers.
But generally it shouldn’t cost more than $50 or $60.
I’m not sure I want to remove the antlers from my deer mount.
Can I just leave them on?
Yes you can leave the antlers on the deer mount if you want.
Will leaving the antlers on the deer mount damage the skull?
No the antlers will not damage the skull if they are left on.
I’m not sure I want to remove the antlers from my deer mount.
Can I just leave them on and put them somewhere else in my house?
Yes you can leave the antlers on the deer mount and put them somewhere else in your house.
I’m not sure I want to remove the antlers from my deer mount.
Can I just leave them on and put them outside?
Yes you can leave the antlers on the deer mount and put them outside.
I’m not sure I want to remove the antlers from my deer mount.
Can I just leave them on and put them in storage?
Yes you can leave the antlers on the deer mount and put them in storage.
